Ultimate Guide to Prepare Free Cisco 200-301 Exam Questions and Answer
Pass Cisco 200-301 Tests Engine pdf - All Free Dumps
IP Connectivity
This objective will test the configuration and verification of OSPFv2 and IPv6 and IPv4 static routing. It will also focus on the routing table, protocol of first-hop redundancy, and routing protocols.
NEW QUESTION 44
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
- A. Set the NTP server private key
- B. Disable NTP broadcasts
- C. Specify the IP address of the NTP server
- D. Verify the time zone.
- E. Enable NTP authentication.
Answer: C,E
Explanation:
To configure authentication, perform this task in privileged mode:
Step 1: Configure an authentication key pair for NTP and specify whether the key will be trusted or untrusted.
Step 2: Set the IP address of the NTP server and the public key.
Step 3: Enable NTP client mode.
Step 4: Enable NTP authentication.
Step 5: Verify the NTP configuration.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8-
2glx/configuration/guide/ ntp.html
NEW QUESTION 45
Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 46
Which output displays a JSON data representation?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: D
Explanation:
JSON data is written as name/value pairs.
A name/value pair consists of a field name (in double quotes), followed by a colon, followed by a value:
"name":"Mark"
JSON can use arrays. Array values must be of type string, number, object, array, boolean or null.
For example:
{
"name":"John",
"age":30,
"cars":[ "Ford", "BMW", "Fiat" ]
}
JSON can have empty object like "taskId":{}
NEW QUESTION 47
Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.
Answer:
Explanation:
NEW QUESTION 48
An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any of three addresses
192.168.30.1, 192.168.3.2, 192.168.3.3 Which configuration should be used?
- A. Option B
- B. Option C
- C. Option D
- D. Option A
Answer: B
NEW QUESTION 49
A network engineer is configuring an OSPFv2 neighbor adjacency Drag and drop the parameters from the left onto their required categories on the right. Not all parameters are used
Answer:
Explanation:
NEW QUESTION 50
Refer to the exhibit.
Which route type is configured to reach the internet?
- A. host route
- B. network route
- C. default route
- D. floating static route
Answer: C
NEW QUESTION 51
Drag and drop the AAA terms from the left onto the description on the right.
Answer:
Explanation:
NEW QUESTION 52
Which value is used to determine the active router in an HSRP default configuration?
- A. Router IP address
- B. Router priority
- C. Router tracking number
- D. Router loopback address
Answer: A
Explanation:
Section: IP Connectivity
Explanation:
Q. If there is no priority configured for a standby group, what determines which router is active?
A. The priority field is used to elect the active router and the standby router for the specific group. In the case of an equal priority, the router with the highest IP address for the respective group is elected as active.
Furthermore, if there are more than two routers in the group, the second highest IP address determines the standby router and the other router/routers are in the listen state.
NEW QUESTION 53
Which command enables a router to become a DHCP client?
- A. ip dhcp client
- B. ip address dhcp
- C. ip dhcp pool
- D. ip helper-address
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dhcp/configuration/12-4/dhcp-12-4-book/config-dhcp-client.html
NEW QUESTION 54 
Refer to the exhibit. An administrator must configure interfaces GM/1 and GM/3 on switch SW11. PC-1 and PC-2 must be placed in the Data VLAN, and Phone-1 must be placed in the Voice VLAN. Which configuration meets these requirements?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: D
NEW QUESTION 55
Refer to the exhibit.
Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
- A. passive
- B. mode on
- C. auto
- D. active
Answer: D
Explanation:
Explanation
From the neighbor status, we notice the "Flags" are SP. "P" here means the neighbor is in Passive mode.In order to create an Etherchannel interface, the (local) SW1 ports should be in Active mode.Moreover, the
"Port State" in the exhibit is "0x3c" (which equals to "00111100 in binary format).Bit 3 is "1" which means the ports are synchronizing -> the ports are working so the local ports should be in Active mode.
NEW QUESTION 56
Refer to the exhibit.
How does the router manage traffic to 192.168.12.16?
- A. It chooses the OSPF route because it has the longest prefix inclusive of the destination address.
- B. It chooses the EIGRP route because it has the lowest administrative distance
- C. it load-balances traffic between all three routes
- D. It selects the RIP route because it has the longest prefix inclusive of the destination address.
Answer: D
NEW QUESTION 57
Which IPv6 address type provides communication between subnets and is unable to route on the Internet?
- A. link-local
- B. unique local
- C. global unicast
- D. multicast
Answer: B
NEW QUESTION 58
Refer to the exhibit.
Which rule does the DHCP server use when there is an IP address conflict?
- A. The address is removed from the pool until the conflict is resolved.
- B. Only the IP detected by Ping is removed from the pool.
- C. Only the IP detected by Gratuitous ARP is removed from the pool.
- D. The address remains in the pool until the conflict is resolved.
- E. The IP will be shown, even after the conflict is resolved.
Answer: A
NEW QUESTION 59
What are two southbound APIs? (Choose two )
- A. Thrift
- B. DSC
- C. NETCONF
- D. OpenFlow
- E. CORBA
Answer: C,D
Explanation:
OpenFlow is a well-known southbound API. OpenFlow defines the way the SDN Controller should interact with the forwarding plane to make adjustments to the network, so it can better adapt to changing business requirements.
The Network Configuration Protocol (NetConf) uses Extensible Markup Language (XML) to install, manipulate and delete configuration to network devices.
NEW QUESTION 60
Refer to the exhibit.
Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
- A. passive
- B. mode on
- C. auto
- D. active
Answer: A
NEW QUESTION 61
Refer to the exhibit.
A network administrator assumes a task to complete the connectivity between PC A and the File Server.
Switch A and Switch B have been partially configured with VLAN 10, 11, 12, and 13. What is the next step in the configuration?
- A. Add a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing.
- B. Add PC A to the same subnet as the Fie Server allowing for intra-VLAN communication.
- C. Add PC A to VLAN 10 and the File Server to VLAN 11 fa VLAN segmentation
- D. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation
Answer: D
NEW QUESTION 62
Which statement about VLAN configuration is true?
- A. The switch must be in VTP server or transparent mode before you can configure a VLAN
- B. Dynamic inter-VLAN routing is supported on VLAN2 through VLAN 4064
- C. A switch in VTP transparent mode save the VLAN databases to the running configuration only
- D. The switch must be in config-vlan mode before you configure an extended VLAN
Answer: A
Explanation:
Section: Network Access
NEW QUESTION 63
Refer to the exhibit.
Which prefix does Router 1 use for traffic to Host A?
- A. 10.10.13.144/28
- B. 10.10.13.0/25
- C. 10.10.10.0/28
- D. 10.10.13.208/29
Answer: D
Explanation:
Explanation
Host A address fall within the address range. However, if more than one route to the same subnet exist (router will use the longest stick match, which match more specific route to the subnet). If there are route
10.10.13.192/26 and 10.10.13.208/29, the router will forward the packet to /29 rather than /28.
NEW QUESTION 64
Where does a switch maintain DHCP snooping information?
- A. In the binding database
- B. In the MAC address table
- C. In the CAM table
- D. In the frame forwarding database
Answer: A
Explanation:
Section: Security Fundamentals
NEW QUESTION 65
......
Cisco Certified Network Associate Exam Practice Tests 2022 | Pass 200-301 with confidence!: https://drive.google.com/open?id=1BTpIg-pCe6HTXvZLl3kldpomVzvI3ij2
Online Exam Practice Tests with detailed explanations!: https://www.dumpstests.com/200-301-latest-test-dumps.html